Sioux-tools 697 Uživatelský manuál stáhnout pdf

CAUTION

Do not at any time attempt to operate this tool without shroud and pad in place.

OPERATION

The sander is designed to operate on 90 p.s.i. air pressure. An air regulator is recommended if pressures are higher than

90 p.s.i. A filter is strongly recommended to provide clean air for long life of the sander.

Lubricate the sander by adding 8-10 drops of air motor oil into the air inlet each day before using.

HOSE AND HOSE CONNECTIONS

Hoses should not be smaller than 3/8" I.D. with 1/4" pipe thread fittings.

LUBRICATION

As mentioned above, 8-10 drops of Sioux air motor oil, Cat. No. 288, should be added to the air intake before using each

day. This will help protect the motor parts from rusting due to water in the air lines and also lubricate the parts for longer

life. Caution should be taken not to add too much oil as it will blow through the tool and may get on the surface being

sanded. An air line oiler will increase the life of the tool. The setting should be about 1 drop of oil per 1-2 minutes of use.

SPEED CONTROL AND SHUT OFF

A speed control and air shut off is located on the bottom of the housing. This

control is adjusted as shown in the diagram. This is to control the speed of

the tool for various sanding operations and to control excessive air pressure.

The control is also used to shut off the air to the tool to safely change sand

paper on the pad.

COUNTER BALANCE

The units are equipped with different counterweights to decrease the vibra-

tion. Following is a chart of pad size and counterweight.

APPROX.

PAD SIZE PAD WEIGHT COUNTER WEIGHT

5" 90-100 Grams 64141 W/Lockout

6" 115-125 Grams 64148 W/Lockout

5" 90-100 Grams 64140 WO/Lockout

6" 115-125 Grams 64147 WO/Lockout

LOSS OF POWER & SPEED

The air motor is probably dirty and sticky. Flush out by adding very light weight oil to the air intake and run unit. Do this

several times until it runs properly. Then add 8-10 drops of Sioux air motor oil, Cat. No. 288, in the air intake and run tool to

lubricate.

WARNING

Continued exposure to vibration may cause injury to your hands or arms.

INSTRUCTIONS & PARTS LIST FOR

NO. 658, 660, 690, 697

SIOUX AIR RANDOM ORBITAL SANDER

INCLUDES B, V, VV, & X SUFFIXES

(SERIAL E)

Form Z262A

Date 1-02/C

Page 1 of 6

Printed In U.S.A.

MAXIMUM SPEED

COUNTERWEIGHT

OFF

1 2 3 4 5 6 7

Shrnutí obsahu

Strany 1 - NO. 658, 660, 690, 697

1CAUTIONDo not at any time attempt to operate this tool without shroud and pad in place.OPERATIONThe sander is designed to operate on 90 p.s.i. air pr

Strany 2

212361626365649101112132728293031323334353637383940414243444546474849501617181920212223242526585857575655545152535959456781415606054555658585959606061

Strany 3

3Fig. PartNo. No. DescriptionFig. PartNo. No. Description*Order Quantity As RequiredFURNISH CATALOG, SERIAL, AND MODEL NUMBERWHEN ORDERING PARTS1. 663

Strany 4 - NO. 690VV, 697VV

4Fig. PartNo. No. Description1. 585V Vacuum Pad 5"583V Vacuum Pad 6"2. 07248 ScrewPan Head #10-32 X 3/4 (Taptite)(4)*3. 65863 RetainerMoto

Strany 5

5NOTES

Strany 6 - Printed In U.S.A

6Printed In U.S.A.El polvo generado al lijar, aserrar, afilar, taladrar y realizar otras tareas de construcción contienesustancias químicas que podría

Strany 7

This pdf incorporates the following model numbers: 658 665 666 690V 690X PS690